View YB1508_4127463.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

YB1508
Step-up DC-DC Converter , White LED Driver Description
The YB1508 is a step-up DC-DC converter, acting as current source to drive up to 8 white LEDs in series. Series connecting of the LEDs provides identical LED currents resulting in uniform brightness and eliminating the need for ballast resistors. The light intensity of these LEDs is proportional to the current passing through them. Additional features include output over voltage protection to prevent device damage due to faulty LED or open circuit caused by abnormal conditions, and one-pin shutdown and multiple methods of dimming control. The YB1508 switches at a fixed frequency of 1MHz, allowing the use of tiny external components and low input noise and ripple. To control LED brightness, the LED current can be pulsed by applying a PWM (pulse width modulated) signal with a frequency range of 100Hz to 50KHz to the CTRL pin. The YB1508 is available in a low profile 5-lead SOT-23 package.
Features
2.7V to 9V input range Adjustable output voltage up to 40V Built in internal switch Inherently matched LED current Fixed frequency of 1MHz PWM operation Open LED protection Low profile 5-Lead SOT-23 package High efficiency: over 80% at 3.6V input voltage Drives up to 8 white LEDs
Applications
LCD Display Module OLED panel/sub-panel White LED Backlighting Digital Camera Cellular Phone Portable Application
Typical Application Circuit
Figure 1Typical Application Circuit YB1508 MRev1.4 WWW.YOBON.COM.TW 1
YB1508
Step-up DC-DC Converter , White LED Driver Pin Description
Figure 2YB1508 SOT23-5
Pin Designator
Table 1 :
Pin 1 2 3 4 5
Name SW GND FB CTRL VIN
Description
Switching Pin. This is the collector of the internal NPN power switch. Connect to inductor and diode. Minimize the metal trace area connected to this pin to reduce EMI. Ground Pin. Connect directly to local ground plane. Feedback Pin. Reference voltage is 200mV. Connect LEDs and a resistor at this pin. LED current is determined by the resistance and CTRL voltage. Shutdown Pin and Dimming Control pin. A. VCTRL > 1.8V generates full-scale LED current B. VCTRL < 0.4V chip is off C. Switching from 0.4V to 2.0V, PWM duty cycle controls the LED current Input Supply Pin. Bypass this pin with a capacitor as close to the device as possible.
Ordering Information
Table 2:
Order Number High Ovp Low Ovp YB1508 YB1508P
Package Type SOT23-5 SOT23-5
Supplied as 3000 units Tape & Reel 3000 units Tape & Reel
Package Marking Y58 Y58P
YB1508 MRev1.4
WWW.YOBON.COM.TW
2
YB1508
Step-up DC-DC Converter , White LED Driver Absolute Maximum Ratings
SW voltage All other pins 40V 10V Maximum Junction Temp,Tj 150 C Lead Temperature (Soldering 10 300 C
sec)
Thermal Resistance
195 C
Electricity Characteristics
Table 3(TA=25C, Vin=3.3V Cin=1uF Cout=4.7uF unless otherwise noted)
Function Parameter Input Voltage Range Feedback Voltage FB Pin Bias current Supply current Switching Frequency Maximum Duty Cycle Minimum duty cycle Switch Vcesat Switch Current Limit Switch Leakage Current VCTRL for Full LED current CTRL Pin Bias Current Chip turn off delay Over Voltage Protection YB1508 YB1508P Ctrl = 2V
Conditions Iout =20mA, Vout = 12.5V Circuit of figure 1. (L=22uH Cout =4.7uF) Rfb = 10 ohms Vfb = 0.3V CTRL = 0V
Min 2.7 180 2
Typ
Max 9
Units V mV A mA A
200 10 3.5 1
220 20
0.7
0.8
1.3 93
MHz % % mV mA A
20 At Isw = 200mA 40% duty cycle Ctrl = 0.3V 1.6
25 200 250 1 1.7 20
35
1.8
V A
30 36 21
S V
YB1508 MRev1.4
WWW.YOBON.COM.TW
3
YB1508
Step-up DC-DC Converter , White LED Driver Functional Block Diagram
Figure 3. Block Diagram
Application Information
Operation The operation of YB1508 can be understood by referring to the block diagram in Figure 3. A voltage proportional to the switch current is added to a ramp output and the resulting sum is fed into the positive terminal of the PWM comparator. When this voltage exceeds the level of the comparator negative input, the peak current has been reached, and the SR latch is reset and turns off the power switch. The voltage at the negative input of the comparator comes from the output of the error amplifier. The error amplifier sets the correct peak current level to keep the output in regulation. If the error amplifier's output increases, more current is delivered to the output; if it decreases, less current is delivered.
small size and high efficiency are major concerns, the inductor should have low core losses at 1MHz and low DCR (copper wire resistance).
Capacitor Selection
The small size of ceramic capacitors makes them ideal for YB1508 applications. X5R and X7R types are recommended because they retain their capacitance over wider voltage and temperature ranges than other types.
Diode selection
To maintain high efficiency, the average current rating of the schottky diode should be larger than the peak inductor current, IPK. Schottky diode with a low forward drop and fast switching speeds are ideal for increasing efficiency in portable applications. The reverse breakdown voltage of the schottky diode must be larger than the output voltage.
Inductor Selection
A 22uH inductor is recommended for most YB1508 applications. Although
YB1508 MRev1.4
WWW.YOBON.COM.TW
4
YB1508
Step-up DC-DC Converter , White LED Driver
Inrush Current The maximum switch current is limited to about 300 mA by the chip. Typically, this large current will occur for about 40us during start up. A larger Cout will increase the duration of high current. However, when Vin is first connected, an even larger current can flow into Cout. This occurs when the SW pin is open circuit and and the Cout voltage changes from 0V to Vin in a few microseconds. Because the duration of this large current is short, it will usually not cause problems. LED Current and Dimming Control The LED current can be reduced by pulse width modulating the CTRL voltage from 0.4V to 1.8V. Using the PWM mode, the LED current can be controlled from 0% to 100%. Open Circuit Protection The YB1508 has an internal open-circuit protection circuit. When the LEDs are disconnected from the circuit or fail open, the YB1508 will then shutdown until Vin goes low or CTRL goes lower than 0.4V. Different maximum Vout can be requested from YoBon. Board Layout Consideration To maximize efficiency, rise and fall times of switch should be made as short as possible. Proper layout of the high frequency switching path is important to prevent electromagnetic interference (EMI) problems. Place COUT close to the VOUT pin. A ground plane under the switching regulator is needed to minimize interplane coupling. In addition, the feedback resistor Rs should be tied directly to the GND Pin without any other connection to ensure a clean, noise-free connection.
Figure 4. Dimming Control Using a DC Voltage
Figure 5. Dimming Control Using a Filtered PWM Signal
YB1508 MRev1.4
WWW.YOBON.COM.TW
5
YB1508
Step-up DC-DC Converter , White LED Driver
Figure 6. Li-Ion to Two White LEDs Application Circuit
Figure 7. Li-Ion to Three White LEDs Application Circuit
Figure 8. Four White LEDs Application Circuit
YB1508 MRev1.4
WWW.YOBON.COM.TW
6
YB1508
Step-up DC-DC Converter , White LED Driver SOT-25 Package Information
All the contents in this datasheet are not assuming any responsibility for use of any circuitry described, no circuit patent license are implied and Yobon reserves the right at any time without notice to change said circuitry and specifications.
YB1508 MRev1.4
WWW.YOBON.COM.TW
7

▲Up To Search▲

Price & Availability of YB1508

	To Download YB1508 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .